Hello everyone, I am Xiao Jia learning to fish, let ’s share with you my Virgo -handmade solid wood drifting box
The reason for the cause of the two oak fingers in the corner of the construction site is as shown in the figure below.
Use the ruler to measure these two pieces of 48 × 16.6 × 1.8cm 25 × 39 × 1.8cm. Immediately in your head, you have an idea to make a drifting box. At night, you will have thoughts. Just do it. The required tools, there are sawing stations, taps, border repair machines, and other tools
Following the master (dad) to work, you have to work well to do this. At four in the afternoon. After all, I have been working with the master for a long time for a long time, and I probably know how to do it with my hand to see the straight edge, then the sawing table settled the size of the pair. good-looking.
For the size of the size of the painting, the size of the painting should be left, and the thickness of the board is 1.8cm. The original 10mm left by 6mm left 6mm. When the 5mm was ready to hollowing out, the master (dad) reminded not to crooked, and it was scrapped when it was crooked. I thought it was full of confidence, and I said it would not be crooked. Why did n’t you look at it? It ’s not strange to use the ruler or not.
This is crooked and can only be trimmed slowly. There is no ruler on the top. The dumpling panel waste plate on the side of the sawtaine is used to block the top with a sawdow on the tape. If you are wrong, you still do n’t change it. This is the same as fishing. It is necessary to change the change to achieve good gains. With a change, it is different, and you can get out a few millimeters a few mm each time, and take too much to destroy things at a time.
After all, I forgot to forget that the speed of the Gaba machine on the side was destroyed. It was really impossible to do everything. It was really unpredictable. It’s broken again.
At noon, I went home to find something to repair. After returning home for meals, I started turning over the box and pouring the cabinet. If I did n’t find it, I saw the welding agent bought by the master (father). Wood, then don’t you want to come and go to the construction site to repair and repair in the afternoon. After the operation of the capable craftsman, it is repaired. Although a little flaw, it does not affect the overall effect.
This also repaired almost the other one also hollowed out the other. With the first lesson of the first car, the second driving was unusually smooth. The picture below can be seen from the width of the side and the narrowness. This is the consequence of not listening to the old man’s words.
Looking at the unevenness of the bottom surface, my obsessive -compulsive patients have to make up for it, and it is not too obvious. In this case, you can use the sawdust. When this thing is hollowed out, a lot of sawdust is used to add glue to sprinkle the sawdust. Thinking of a layer of sawdust for white latex brushing
As soon as I saw that the sawdust was too dry, I fiddled with a little diluted white latex brush, dried for a while, and the plate was deformed. It was really insufficient. Find a way, I am embarrassed to ask the master (dad) to deal with it. Strang away the white latex with a sawdust. The flat floor brick is pressed on the top. This is not to be seen for the old iron. I was shameful to get home. It is really the son of the old carpenter for decades. When I made solid wood furniture, I still went to elementary school when I made solid wood furniture. Now follow the master’s dry panel without painting, so it is done. Back to the topic, it was still embarrassing after the next night when I looked at it, and it was cracked. Thinking of the wetness inside, then the two pieces were wet on the outside and pushing a box of skirting lines on the top. This time, the stone was heavier after repeated wetness and finally returned to the original. The glue also finished the recessed place, and buy more glue at a certain amount of glue at the open seam. Practic. These steps are not taken.
After more than half a month (empty) processing, it finally arrived at the above pattern material. The computer printing pattern was transferred to the board. Hand -made two -character hand -carved
Start painting the first time, and it takes 12 hours to dry. Get it over again
Today, because in the group of fishermen, it was said that the fish was a bit like wheat ears, which was really a bit small. Come back to the sandpaper at night to polish and re -draw, it is really difficult to polish after painting. No response for a long time, 240 sandpaper is still too thin, finding 60 sand cloth to polish, kung fu is not responsible for people, firmly believes that the concept of iron pestle grinding into a needle is polished and finally polished. Continue to draw a painting, it is 11 o’clock in the middle of the night after 8 o’clock. Come again with wood oil. End today.
After waiting for a long time, I have time to continue to clean up my Virgo on the pages. The minor pages are a bit small, and I can only open it with a small union. The upper page of the bottom of the velvet is sticked after the velvet cloth sticker floating card seat directly depends on the effect
I still did n’t have the magnetic drill and the drill head. When I had time, I was simply installed with a strong magnetic.
On the other side, the non -slip buckle of the two daughters -in -the -daughter -in -law’s two -daughter -in -law’s nails in the figure below is not allowed to be discovered. Or you know. Choose the plastic head on the nail head to soften it with fire and then order it on the wooden strip. It is completed in the pill.
For the first time, I was forgiven for bad doing it. The intermittent deduction time was discovered from November 31, 2021 to the production of the material to complete the January 12th calendar 2022. Twelve days a month
Welcome DIY experts to give suggestions. Contempt with an open mind.
Let’s enjoy below